HCDX-Y8 AC Portable Yoke Magnetic Yoke Flaw Detector
HCDX-Y8 is our latest developed AC yoke. It is used for magnetic
particle flaw detection and local magnetization of the workpiece.
The machine is compact and durable, and is one of the lowest weight
and largest span AC yoke on the market. Lifting force and other indicators meet the
requirements of GB/T 15822.3-2005/ISO 9934-3:2002, ASME V and other
standards.
1. Machine structure
| Item | Part Number | Item | Part Number |
| 1 | Yoke | 5 | Power Cable |
| 2 | Inductive LED lighting | 6 | Aviation connector cover connection cable |
| (Optional accessories) |
| 3 | Yoke foot | 7 | Aviation coupling cover |
| 4 | microswitch | 8 | AC Power Cable |
2. Usage method
Connect the power cable to the host and plug the AC plug into the
220V power socket.
Place the two magnetic poles of HCDX-Y8 on the surface of the
detected object, and apply certain pressure to make the two
magnetic poles in good contact with the detected object. Press the
button switch, turn on, start magnetization, loosen, magnetization
ends. When the yoke switch is turned on, the magnetic powder is
applied to the surface of the detected object (dry, wet,
fluorescent magnetic powder can be applied).
If the surface to be examined is too wide, it shall be magnetized
in sections, and the effective parts between the sections shall
overlap to a certain extent.
Rotate the movable joint between the magnetic feet, and the
distance between the magnetic feet can be adjusted between 45mm and
225mm.
When using should pass 5 seconds off 5 seconds, can be used
continuously for 4 hours.
3. Technical parameters
3.1 Yoke
| Item | Indicator | Item | Indicator | |
| Yoke Weight | 2.35Kg | Sensitivity | The 30/100A test piece is clearly displayed | |
| Power supply | AC:220V/50Hz | Lifting power | ≥4.5Kg | |
| Electric current | No-load | 1.4A | Temporary load rate | On 5 seconds, off 5 seconds, continuous use of more than 4 hours | |
| Load | 1.0A | Temperature rise | Handle surface temperature ≤40 ° C | |
| Magnetic electrode distance | 45~225mm | Insulation strength | >2MΩ | |
| Power cord length (spring wire) | 4m | Size of magnetic foot contact surface | 20×21mm | |
|
4.
Attention
Please check the power cord and plug for damage before use.
Do not keep close contact with other electrical equipment during
use. Strong magnetic fields have destructive effects on watches,
mobile phones, etc.
Do not hold the yoke in the conduction state for a long time (such
as dragging line on the weld), should be on for 5 seconds and off
for 5 seconds.
In the DC state, disconnect the connection line between the battery
and the magnetic yoke after the end of the work, and the battery
should be stored in a cool and dry place, strictly prohibited in
the sun, otherwise there is a danger of explosion. Please
disconnect the power supply after charging.
In rainy weather, please do not work outdoors, rain will cause
short circuit or leakage.
The unit is completely waterproof except at the power junction.
Please pay attention when applying magnetic suspension.
If the device has abnormal noise or odor, turn off the power
immediately.
Do not move the device by pulling the power cable. This will damage
the power cable.
If the equipment is abnormal, do not repair it without
authorization, please contact the dealer or contact our after-sales
service center directly.
Check whether there is iron dust on the connector of the power
cable. Metal dust can cause short circuits.
After use, the magnetic powder on the magnetic pole should be
cleaned up and applied with anti-rust oil to prevent it from
rusting and sticking.
5. Configure the table
| Iiem | Name | Quantity |
| 1 | Host | 1 |
| 2 | 220V Power Cable | 1 |
| 3 | Yoke strap | 1 |
| 4 | Yoke backpack | 1 |
| 5 | Hex key 3mm | 1 |
| 6 | Manual | 1 |
| 7 | Calibration certificate | 1 |
Note: This machine can be optional charger, battery, cable, optional can
be converted into DC yoke. Optional induction LED lighting and
inclined magnetic feet.
7. Quality guarantee
Thank you for choosing our HCDX-Y8 AC portable yoke, our company
strictly in accordance with ISO 9001-2008 quality system
management. Each equipment is tested and issued by the quality
department of the company. This product meets the requirements of
GB/T 15822.3-2005/ISO 9934-3-2002, ASME V and other standards.
The warranty period of this product is 1 year, under normal use,
any failure of the product will be repaired by the company free of
charge (free material and maintenance costs), and preferential paid
maintenance will be provided within 3 years.
